Thread: wireless not connecting winstars-N WS-WNP671N PCI (Ralink RT2860STA)

i use ubuntu 11.04 on pc clone desktop.
ethernet cable connects automatically, despite compiling wlan0
not connected. not know installed ubuntu 10.04 , 11.04 on 30 times , still same. try manually connect network connection did not work either hidden , deal ipv4 address assigned , neither worked.

1 ) machine brand , model (pc/laptop):
desktop pc, clon.

2)lspci
00:00.0 host bridge: ati technologies inc rs690 host bridge
00:02.0 pci bridge: ati technologies inc rs690 pci pci bridge (pci express graphics port 0)
00:05.0 pci bridge: ati technologies inc rs690 pci pci bridge (pci express port 1)
00:11.0 sata controller: ati technologies inc sb7x0/sb8x0/sb9x0 sata controller [ide mode]
00:12.0 usb controller: ati technologies inc sb7x0/sb8x0/sb9x0 usb ohci0 controller
00:12.1 usb controller: ati technologies inc sb7x0 usb ohci1 controller
00:12.2 usb controller: ati technologies inc sb7x0/sb8x0/sb9x0 usb ehci controller
00:13.0 usb controller: ati technologies inc sb7x0/sb8x0/sb9x0 usb ohci0 controller
00:13.1 usb controller: ati technologies inc sb7x0 usb ohci1 controller
00:13.2 usb controller: ati technologies inc sb7x0/sb8x0/sb9x0 usb ehci controller
00:14.0 smbus: ati technologies inc sbx00 smbus controller (rev 3a)
00:14.1 ide interface: ati technologies inc sb7x0/sb8x0/sb9x0 ide controller
00:14.2 audio device: ati technologies inc sbx00 azalia (intel hda)
00:14.3 isa bridge: ati technologies inc sb7x0/sb8x0/sb9x0 lpc host controller
00:14.4 pci bridge: ati technologies inc sbx00 pci pci bridge
00:14.5 usb controller: ati technologies inc sb7x0/sb8x0/sb9x0 usb ohci2 controller
00:18.0 host bridge: advanced micro devices [amd] family 10h processor hypertransport configuration
00:18.1 host bridge: advanced micro devices [amd] family 10h processor address map
00:18.2 host bridge: advanced micro devices [amd] family 10h processor dram controller
00:18.3 host bridge: advanced micro devices [amd] family 10h processor miscellaneous control
00:18.4 host bridge: advanced micro devices [amd] family 10h processor link control
01:00.0 vga compatible controller: ati technologies inc rv710 [radeon hd 4350]
01:00.1 audio device: ati technologies inc rv710/730
02:00.0 ethernet controller: realtek semiconductor co., ltd. rtl8101e/rtl8102e pci express fast ethernet controller (rev 02)
03:00.0 network controller: ralink corp. device 3062

3)ifconfig
eth0 link encap:ethernet direcciónhw 10:78:d2:89:33:46
direc. inet:192.168.1.101 difus.:192.168.1.255 másc:255.255.255.0
dirección inet6: fe80::1278:d2ff:fe89:3346/64 alcance:enlace
activo difusiÓn funcionando multicast mtu:1500 métrica:1
paquetes rx:1912 errores:0 perdidos:0 overruns:0 frame:0
paquetes tx:1654 errores:0 perdidos:0 overruns:0 carrier:0
colisiones:0 long.colatx:1000
bytes rx:2076491 (2.0 mb) tx bytes:207618 (207.6 kb)
interrupción:42 dirección base: 0x6000

lo link encap:bucle local
direc. inet:127.0.0.1 másc:255.0.0.0
dirección inet6: ::1/128 alcance:anfitrión
activo bucle funcionando mtu:16436 métrica:1
paquetes rx:20 errores:0 perdidos:0 overruns:0 frame:0
paquetes tx:20 errores:0 perdidos:0 overruns:0 carrier:0
colisiones:0 long.colatx:0
bytes rx:1200 (1.2 kb) tx bytes:1200 (1.2 kb)

wlan0 link encap:ethernet direcciónhw 00:0c:0b:44:b8:4a
activo difusiÓn multicast mtu:1500 métrica:1
paquetes rx:0 errores:0 perdidos:0 overruns:0 frame:0
paquetes tx:0 errores:0 perdidos:0 overruns:0 carrier:0
colisiones:0 long.colatx:1000
bytes rx:0 (0.0 b) tx bytes:0 (0.0 b)

iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 ieee 802.11bgn essidff/any
mode:managed access point: not-associated tx-power=20 dbm
retry long limit:7 rts thrff fragment thr:ff
power management:ff

iwconfig wlan0
wlan0 ieee 802.11bgn essidff/any
mode:managed access point: not-associated tx-power=20 dbm
retry long limit:7 rts thrff fragment thrff
power managementff

4)lsmod
module size used by
binfmt_misc 13213 1
vesafb 13449 1
snd_hda_codec_hdmi 27479 1
snd_hda_codec_via 56765 1
snd_hda_intel 24140 2
snd_hda_codec 90901 3 snd_hda_codec_hdmi,snd_hda_codec_via,snd_hda_intel
snd_hwdep 13274 1 snd_hda_codec
snd_pcm 80244 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_seq_midi 13132 0
arc4 12473 2
snd_rawmidi 25269 1 snd_seq_midi
snd_seq_midi_event 14475 1 snd_seq_midi
snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event
rt2800pci 18159 0
rt2800lib 43824 1 rt2800pci
crc_ccitt 12595 1 rt2800lib
rt2x00pci 13986 1 rt2800pci
ppdev 12849 0
snd_timer 28659 2 snd_pcm,snd_seq
snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq
sp5100_tco 13456 0
psmouse 73312 0
parport_pc 32111 1
serio_raw 12990 0
lp 13349 0
i2c_piix4 13095 0
snd 55295 14 snd_hda_codec_hdmi,snd_hda_codec_via,snd_hda_intel ,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_s eq,snd_timer,snd_seq_device
fglrx 2434640 128
rt2x00lib 39075 3 rt2800pci,rt2800lib,rt2x00pci
parport 36746 3 ppdev,parport_pc,lp
soundcore 12600 1 snd
mac80211 257001 3 rt2800lib,rt2x00pci,rt2x00lib
cfg80211 156212 2 rt2x00lib,mac80211
snd_page_alloc 14073 2 snd_hda_intel,snd_pcm
eeprom_93cx6 12653 1 rt2800pci
ati_agp 13202 0
k10temp 12951 0
usb_storage 43946 0
uas 17676 0
ahci 21591 3
libahci 25548 1 ahci
r8169 42534 0
pata_atiixp 12968 0

5) $dmesg
[ 0.384458] system 00:0e: [mem 0xfec00000-0xffffffff] not reserved
[ 0.384462] system 00:0e: plug , play acpi device, ids pnp0c01 (active)
[ 0.384535] pnp: pnp acpi: found 15 devices
[ 0.384536] acpi: acpi bus type pnp unregistered
[ 0.384539] pnpbios: disabled acpi pnp
[ 0.420185] pci 0000:00:02.0: pci bridge [bus 01-01]
[ 0.420187] pci 0000:00:02.0: bridge window [io 0xd000-0xdfff]
[ 0.420190] pci 0000:00:02.0: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.420193] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.420196] pci 0000:00:05.0: pci bridge [bus 02-02]
[ 0.420198] pci 0000:00:05.0: bridge window [io 0xe000-0xefff]
[ 0.420201] pci 0000:00:05.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.420203] pci 0000:00:05.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.420206] pci 0000:00:14.4: pci bridge [bus 03-03]
[ 0.420208] pci 0000:00:14.4: bridge window [io disabled]
[ 0.420212] pci 0000:00:14.4: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.420216] pci 0000:00:14.4: bridge window [mem pref disabled]
[ 0.420226] pci 0000:00:02.0: setting latency timer 64
[ 0.420229] pci 0000:00:05.0: setting latency timer 64
[ 0.420236] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.420238] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.420239] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.420241] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.420243] pci_bus 0000:00: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.420245] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.420247] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.420248] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff]
[ 0.420250] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.420252] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.420254] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.420256] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.420258] pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.420260] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
[ 0.420261] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
[ 0.420263] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.420265] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.420267] pci_bus 0000:03: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.420269] pci_bus 0000:03: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.420293] net: registered protocol family 2
[ 0.420338] ip route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.420484] tcp established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.420880] tcp bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.421101] tcp: hash tables configured (established 131072 bind 65536)
[ 0.421103] tcp reno registered
[ 0.421105] udp hash table entries: 512 (order: 2, 16384 bytes)
[ 0.421113] udp-lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.421192] net: registered protocol family 1
[ 1.188056] pci 0000:01:00.0: boot video device
[ 1.188066] pci: cls 64 bytes, default 64
[ 1.188225] cpufreq-nforce2: no nforce2 chipset.
[ 1.188314] audit: initializing netlink socket (disabled)
[ 1.188321] type=2000 audit(1308942682.184:1): initialized
[ 1.195418] highmem bounce pool size: 64 pages
[ 1.195422] hugetlb registered 4 mb page size, pre-allocated 0 pages
[ 1.196676] vfs: disk quotas dquot_6.5.2
[ 1.196728] dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.197247] fuse init (api version 7.16)
[ 1.197368] msgmni has been set 1702
[ 1.197629] block layer scsi generic (bsg) driver version 0.4 loaded (major 253)
[ 1.197659] io scheduler noop registered
[ 1.197661] io scheduler deadline registered
[ 1.197687] io scheduler cfq registered (default)
[ 1.197782] pcieport 0000:00:02.0: setting latency timer 64
[ 1.197808] pcieport 0000:00:02.0: irq 40 msi/msi-x
[ 1.197842] pcieport 0000:00:05.0: setting latency timer 64
[ 1.197859] pcieport 0000:00:05.0: irq 41 msi/msi-x
[ 1.197904] pci_hotplug: pci hot plug pci core version: 0.5
[ 1.197921] pciehp: pci express hot plug controller driver version: 0.4
[ 1.198023] input: power button /devices/lnxsystm:00/device:00/pnp0c0c:00/input/input0
[ 1.224045] acpi: power button [pwrb]
[ 1.224104] input: power button /devices/lnxsystm:00/lnxpwrbn:00/input/input1
[ 1.224107] acpi: power button [pwrf]
[ 1.224215] acpi: acpi_idle registered cpuidle
[ 1.244539] thermal lnxtherm:00: registered thermal_zone0
[ 1.244541] acpi: thermal zone [thrm] (30 c)
[ 1.244575] erst: table not found!
[ 1.244633] isapnp: scanning pnp cards...
[ 1.244658] serial: 8250/16550 driver, 32 ports, irq sharing enabled
[ 1.265127] serial8250: ttys0 @ i/o 0x3f8 (irq = 4) 16550a
[ 1.598532] isapnp: no plug & play device found
[ 1.692705] 00:05: ttys0 @ i/o 0x3f8 (irq = 4) 16550a
[ 1.696329] linux agpgart interface v0.103
[ 1.697272] brd: module loaded
[ 1.697630] loop: module loaded
[ 1.697688] i2c-core: driver [adp5520] using legacy suspend method
[ 1.697690] i2c-core: driver [adp5520] using legacy resume method
[ 1.697779] pata_acpi 0000:00:14.1: pci int -> gsi 16 (level, low) -> irq 16
[ 1.697800] pata_acpi 0000:00:14.1: setting latency timer 64
[ 1.698018] fixed mdio bus: probed
[ 1.698042] ppp generic driver version 2.4.2
[ 1.698067] tun: universal tun/tap device driver, 1.6
[ 1.698068] tun: (c) 1999-2004 max krasnyansky <maxk@qualcomm.com>
[ 1.698123] ehci_hcd: usb 2.0 'enhanced' host controller (ehci) driver
[ 1.698135] ehci_hcd 0000:00:12.2: pci int b -> gsi 17 (level, low) -> irq 17
[ 1.698144] ehci_hcd 0000:00:12.2: ehci host controller
[ 1.698167] ehci_hcd 0000:00:12.2: new usb bus registered, assigned bus number 1
[ 1.698213] ehci_hcd 0000:00:12.2: applying amd sb700/sb800/hudson-2/3 ehci dummy qh workaround
[ 1.698227] ehci_hcd 0000:00:12.2: applying amd sb600/sb700 usb freeze workaround
[ 1.698240] ehci_hcd 0000:00:12.2: debug port 1
[ 1.698310] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe8ff800
[ 1.708043] ehci_hcd 0000:00:12.2: usb 2.0 started, ehci 1.00
[ 1.708160] hub 1-0:1.0: usb hub found
[ 1.708163] hub 1-0:1.0: 6 ports detected
[ 1.708240] ehci_hcd 0000:00:13.2: pci int b -> gsi 19 (level, low) -> irq 19
[ 1.708256] ehci_hcd 0000:00:13.2: ehci host controller
[ 1.708284] ehci_hcd 0000:00:13.2: new usb bus registered, assigned bus number 2
[ 1.708331] ehci_hcd 0000:00:13.2: applying amd sb700/sb800/hudson-2/3 ehci dummy qh workaround
[ 1.708347] ehci_hcd 0000:00:13.2: applying amd sb600/sb700 usb freeze workaround
[ 1.708360] ehci_hcd 0000:00:13.2: debug port 1
[ 1.708385] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe8ff400
[ 1.720041] ehci_hcd 0000:00:13.2: usb 2.0 started, ehci 1.00
[ 1.720165] hub 2-0:1.0: usb hub found
[ 1.720168] hub 2-0:1.0: 6 ports detected
[ 1.720232] ohci_hcd: usb 1.1 'open' host controller (ohci) driver
[ 1.720246] ohci_hcd 0000:00:12.0: pci int -> gsi 16 (level, low) -> irq 16
[ 1.720262] ohci_hcd 0000:00:12.0: ohci host controller
[ 1.720289] ohci_hcd 0000:00:12.0: new usb bus registered, assigned bus number 3
[ 1.720363] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe8fe000
[ 1.780152] hub 3-0:1.0: usb hub found
[ 1.780158] hub 3-0:1.0: 3 ports detected
[ 1.780218] ohci_hcd 0000:00:12.1: pci int -> gsi 16 (level, low) -> irq 16
[ 1.780233] ohci_hcd 0000:00:12.1: ohci host controller
[ 1.780264] ohci_hcd 0000:00:12.1: new usb bus registered, assigned bus number 4
[ 1.784084] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe8fd000
[ 1.844141] hub 4-0:1.0: usb hub found
[ 1.844148] hub 4-0:1.0: 3 ports detected
[ 1.844217] ohci_hcd 0000:00:13.0: pci int -> gsi 18 (level, low) -> irq 18
[ 1.844233] ohci_hcd 0000:00:13.0: ohci host controller
[ 1.844259] ohci_hcd 0000:00:13.0: new usb bus registered, assigned bus number 5
[ 1.844329] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe8fc000
[ 1.904156] hub 5-0:1.0: usb hub found
[ 1.904162] hub 5-0:1.0: 3 ports detected
[ 1.904222] ohci_hcd 0000:00:13.1: pci int -> gsi 18 (level, low) -> irq 18
[ 1.904237] ohci_hcd 0000:00:13.1: ohci host controller
[ 1.904265] ohci_hcd 0000:00:13.1: new usb bus registered, assigned bus number 6
[ 1.908085] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe8fb000
[ 1.968141] hub 6-0:1.0: usb hub found
[ 1.968147] hub 6-0:1.0: 3 ports detected
[ 1.968207] ohci_hcd 0000:00:14.5: pci int c -> gsi 18 (level, low) -> irq 18
[ 1.968224] ohci_hcd 0000:00:14.5: ohci host controller
[ 1.968256] ohci_hcd 0000:00:14.5: new usb bus registered, assigned bus number 7
[ 1.968319] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe8fa000
[ 2.028161] hub 7-0:1.0: usb hub found
[ 2.028167] hub 7-0:1.0: 2 ports detected
[ 2.028226] uhci_hcd: usb universal host controller interface driver
[ 2.028345] i8042: pnp: ps/2 controller [pnp0303:s2k,pnp0f03:s2m] @ 0x60,0x64 irq 1,12
[ 2.028729] serio: i8042 kbd port @ 0x60,0x64 irq 1
[ 2.028737] serio: i8042 aux port @ 0x60,0x64 irq 12
[ 2.028858] mousedev: ps/2 mouse device common mice
[ 2.028944] rtc_cmos 00:02: rtc can wake s4
[ 2.032054] usb 2-3: new high speed usb device using ehci_hcd , address 2
[ 2.032163] rtc_cmos 00:02: rtc core: registered rtc_cmos rtc0
[ 2.032190] rtc0: alarms 1 month, y3k, 114 bytes nvram, hpet irqs
[ 2.032266] device-mapper: uevent: version 1.0.3
[ 2.032328] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com
[ 2.032415] device-mapper: multipath: version 1.2.0 loaded
[ 2.032419] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.032509] eisa: probing bus 0 @ eisa.0
[ 2.032511] eisa: cannot allocate resource mainboard
[ 2.032512] cannot allocate resource eisa slot 1
[ 2.032514] cannot allocate resource eisa slot 2
[ 2.032515] cannot allocate resource eisa slot 3
[ 2.032516] cannot allocate resource eisa slot 4
[ 2.032517] cannot allocate resource eisa slot 5
[ 2.032518] cannot allocate resource eisa slot 6
[ 2.032520] cannot allocate resource eisa slot 7
[ 2.032521] cannot allocate resource eisa slot 8
[ 2.032522] eisa: detected 0 cards.
[ 2.032617] cpuidle: using governor ladder
[ 2.032619] cpuidle: using governor menu
[ 2.032807] tcp cubic registered
[ 2.032893] net: registered protocol family 10
[ 2.033295] net: registered protocol family 17
[ 2.033306] registering dns_resolver key type
[ 2.033332] powernow-k8: found 1 amd athlon(tm) ii x2 250 processor (2 cpu cores) (version 2.20.00)
[ 2.033362] powernow-k8: 0 : pstate 0 (3000 mhz)
[ 2.033364] powernow-k8: 1 : pstate 1 (2300 mhz)
[ 2.033365] powernow-k8: 2 : pstate 2 (1800 mhz)
[ 2.033366] powernow-k8: 3 : pstate 3 (800 mhz)
[ 2.033481] using ipi no-shortcut mode
[ 2.033556] pm: hibernation image not present or not loaded.
[ 2.033563] registered taskstats version 1
[ 2.033759] magic number: 15:435:193
[ 2.033798] acpi device:1f: hash matches
[ 2.033845] rtc_cmos 00:02: setting system clock 2011-06-24 19:11:23 utc (1308942683)
[ 2.033847] bios edd facility v0.16 2004-jun-25, 0 devices found
[ 2.033849] edd information not available.
[ 2.033919] freeing unused kernel memory: 700k freed
[ 2.034107] write protecting kernel text: 5192k
[ 2.034137] write protecting kernel read-only data: 2148k
[ 2.046970] input: @ translated set 2 keyboard /devices/platform/i8042/serio0/input/input2
[ 2.053915] <30>udev[62]: starting version 167
[ 2.121593] r8169 gigabit ethernet driver 2.3lk-napi loaded
[ 2.121609] r8169 0000:02:00.0: pci int -> gsi 17 (level, low) -> irq 17
[ 2.121639] r8169 0000:02:00.0: setting latency timer 64
[ 2.121683] r8169 0000:02:00.0: irq 42 msi/msi-x
[ 2.122051] r8169 0000:02:00.0: eth0: rtl8102e @ 0xf8036000, 10:78:d2:89:33:46, xid 04c00000 irq 42
[ 2.138339] scsi0 : pata_atiixp
[ 2.143780] scsi1 : pata_atiixp
[ 2.144300] ata1: pata max udma/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 2.144303] ata2: pata max udma/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 2.144552] ahci 0000:00:11.0: version 3.0
[ 2.144569] ahci 0000:00:11.0: pci int -> gsi 22 (level, low) -> irq 22
[ 2.144666] ahci 0000:00:11.0: ahci 0001.0100 32 slots 4 ports 3 gbps 0xf impl sata mode
[ 2.144669] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
[ 2.145539] scsi2 : ahci
[ 2.145598] scsi3 : ahci
[ 2.145653] scsi4 : ahci
[ 2.145709] scsi5 : ahci
[ 2.145793] ata3: sata max udma/133 abar m1024@0xfe8ffc00 port 0xfe8ffd00 irq 22
[ 2.145796] ata4: sata max udma/133 abar m1024@0xfe8ffc00 port 0xfe8ffd80 irq 22
[ 2.145798] ata5: sata max udma/133 abar m1024@0xfe8ffc00 port 0xfe8ffe00 irq 22
[ 2.145801] ata6: sata max udma/133 abar m1024@0xfe8ffc00 port 0xfe8ffe80 irq 22
[ 2.170708] usbcore: registered new interface driver uas
[ 2.188049] refined tsc clocksource calibration: 2993.498 mhz.
[ 2.188054] switching clocksource tsc
[ 2.316681] ata2.00: ata-7: maxtor 6e030l0, nar61590, max udma/133
[ 2.316684] ata2.00: 60058656 sectors, multi 16: lba
[ 2.316689] ata2.00: limited udma/33 due 40-wire cable
[ 2.332614] ata2.00: configured udma/33
[ 2.332784] scsi 1:0:0:0: direct-access ata maxtor 6e030l0 nar6 pq: 0 ansi: 5
[ 2.332937] sd 1:0:0:0: [sda] 60058656 512-byte logical blocks: (30.7 gb/28.6 gib)
[ 2.332945] sd 1:0:0:0: attached scsi generic sg0 type 0
[ 2.332968] sd 1:0:0:0: [sda] write protect off
[ 2.332971] sd 1:0:0:0: [sda] mode sense: 00 3a 00 00
[ 2.332988] sd 1:0:0:0: [sda] write cache: enabled, read cache: enabled, doesn't support dpo or fua
[ 2.335590] sda: sda1
[ 2.335811] sd 1:0:0:0: [sda] attached scsi disk
[ 2.464072] ata6: sata link down (sstatus 0 scontrol 300)
[ 2.464137] ata5: sata link down (sstatus 0 scontrol 300)
[ 2.636043] ata4: softreset failed (device not ready)
[ 2.636047] ata4: applying sb600 pmp srst workaround , retrying
[ 2.636066] ata3: softreset failed (device not ready)
[ 2.636068] ata3: applying sb600 pmp srst workaround , retrying
[ 2.808039] ata4: sata link 1.5 gbps (sstatus 113 scontrol 300)
[ 2.808066] ata3: sata link 3.0 gbps (sstatus 123 scontrol 300)
[ 2.810525] ata4.00: atapi: atapi ihas122, zl07, max udma/100
[ 2.811375] ata4.00: configured udma/100
[ 2.814475] ata3.00: ata-7: samsung hd161gj, 1ac01118, max udma7
[ 2.814478] ata3.00: 312581808 sectors, multi 16: lba48 ncq (depth 31/32), aa
[ 2.820984] ata3.00: configured udma/133
[ 2.821137] scsi 2:0:0:0: direct-access ata samsung hd161gj 1ac0 pq: 0 ansi: 5
[ 2.821284] sd 2:0:0:0: attached scsi generic sg1 type 0
[ 2.821317] sd 2:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 gb/149 gib)
[ 2.821356] sd 2:0:0:0: [sdb] write protect off
[ 2.821358] sd 2:0:0:0: [sdb] mode sense: 00 3a 00 00
[ 2.821372] sd 2:0:0:0: [sdb] write cache: enabled, read cache: enabled, doesn't support dpo or fua
[ 2.822723] scsi 3:0:0:0: cd-rom atapi ihas122 zl07 pq: 0 ansi: 5
[ 2.826095] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.826099] cdrom: uniform cd-rom driver revision: 3.20
[ 2.826219] sr 3:0:0:0: attached scsi cd-rom sr0
[ 2.826284] sr 3:0:0:0: attached scsi generic sg2 type 5
[ 2.865001] sdb: sdb1 < sdb5 sdb6 sdb7 > sdb2 sdb3
[ 2.865305] sd 2:0:0:0: [sdb] attached scsi disk
[ 2.869883] initializing usb mass storage driver...
[ 2.870790] scsi6 : usb-storage 2-3:1.0
[ 2.870997] usbcore: registered new interface driver usb-storage
[ 2.870999] usb mass storage support registered.
[ 3.395104] ext4-fs (sdb5): mounted filesystem ordered data mode. opts: (null)
[ 3.868869] scsi 6:0:0:0: direct-access generic usb sd reader 1.00 pq: 0 ansi: 0
[ 3.869496] scsi 6:0:0:1: direct-access generic usb cf reader 1.01 pq: 0 ansi: 0
[ 3.870156] scsi 6:0:0:2: direct-access generic usb sm reader 1.02 pq: 0 ansi: 0
[ 3.870743] scsi 6:0:0:3: direct-access generic usb ms reader 1.03 pq: 0 ansi: 0
[ 3.871141] sd 6:0:0:0: attached scsi generic sg3 type 0
[ 3.871243] sd 6:0:0:1: attached scsi generic sg4 type 0
[ 3.871331] sd 6:0:0:2: attached scsi generic sg5 type 0
[ 3.871420] sd 6:0:0:3: attached scsi generic sg6 type 0
[ 3.877487] sd 6:0:0:0: [sdc] attached scsi removable disk
[ 3.879738] sd 6:0:0:1: [sdd] attached scsi removable disk
[ 3.880486] sd 6:0:0:2: [sde] attached scsi removable disk
[ 3.881235] sd 6:0:0:3: [sdf] attached scsi removable disk
[ 4.808630] adding 1994748k swap on /dev/sdb7. priority:-1 extents:1 across:1994748k
[ 5.010887] <30>udev[370]: starting version 167
[ 6.286318] type=1400 audit(1308953487.749:2): apparmor="status" operation="profile_load" name="/sbin/dhclient" pid=563 comm="apparmor_parser"
[ 6.286582] type=1400 audit(1308953487.749:3): apparmor="status" operation="profile_load" name="/usr/lib/networkmanager/nm-dhcp-client.action" pid=563 comm="apparmor_parser"
[ 6.286752] type=1400 audit(1308953487.749:4): apparmor="status" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=563 comm="apparmor_parser"
[ 6.286903] type=1400 audit(1308953487.749:5): apparmor="status" operation="profile_replace" name="/sbin/dhclient" pid=538 comm="apparmor_parser"
[ 6.287171] type=1400 audit(1308953487.749:6): apparmor="status" operation="profile_replace" name="/usr/lib/networkmanager/nm-dhcp-client.action" pid=538 comm="apparmor_parser"
[ 6.287347] type=1400 audit(1308953487.749:7): apparmor="status" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=538 comm="apparmor_parser"
[ 6.455591] cfg80211: calling crda update world regulatory domain
[ 6.729293] fglrx: module license 'proprietary. (c) 2002 - ati technologies, starnberg, germany' taints kernel.
[ 6.729297] disabling lock debugging due kernel taint
[ 6.776397] [fglrx] maximum main memory use locked dma buffers: 1884 mbytes.
[ 6.776557] [fglrx] vendor: 1002 device: 954f count: 1
[ 6.776897] [fglrx] ioport: bar 4, base 0xd000, size: 0x100
[ 6.776907] pci 0000:01:00.0: pci int -> gsi 18 (level, low) -> irq 18
[ 6.776912] pci 0000:01:00.0: setting latency timer 64
[ 6.777124] [fglrx] kernel pat support enabled
[ 6.777141] [fglrx] module loaded - fglrx 8.84.60 [mar 24 2011] 1 minors
[ 6.786005] piix4_smbus 0000:00:14.0: smbus host controller @ 0xb00, revision 0
[ 6.790425] lp: driver loaded no devices found
[ 6.808075] parport_pc 00:06: reported plug , play acpi
[ 6.808128] parport0: pc-style @ 0x378, irq 7 [pcspp]
[ 6.848273] sp5100 tco timer: sp5100 tco watchdog timer driver v0.01
[ 6.848387] sp5100 tco timer: mmio address 0xfec000f0 in use
[ 6.904155] lp0: using parport0 (interrupt-driven).
[ 6.940118] ppdev: user-space parallel port driver
[ 6.954234] psmouse serio1: id: 10 00 64
[ 7.193032] rt2800pci 0000:03:00.0: pci int -> gsi 20 (level, low) -> irq 20
[ 7.194977] cfg80211: updating information on frequency 2412 mhz 20 mhz width channel regulatory rule:
[ 7.194979] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194981] cfg80211: updating information on frequency 2417 mhz 20 mhz width channel regulatory rule:
[ 7.194983] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194985] cfg80211: updating information on frequency 2422 mhz 20 mhz width channel regulatory rule:
[ 7.194986] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194988] cfg80211: updating information on frequency 2427 mhz 20 mhz width channel regulatory rule:
[ 7.194990] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194991] cfg80211: updating information on frequency 2432 mhz 20 mhz width channel regulatory rule:
[ 7.194993] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194995] cfg80211: updating information on frequency 2437 mhz 20 mhz width channel regulatory rule:
[ 7.194997] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.194998] cfg80211: updating information on frequency 2442 mhz 20 mhz width channel regulatory rule:
[ 7.195000] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195002] cfg80211: updating information on frequency 2447 mhz 20 mhz width channel regulatory rule:
[ 7.195003] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195005] cfg80211: updating information on frequency 2452 mhz 20 mhz width channel regulatory rule:
[ 7.195007] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195008] cfg80211: updating information on frequency 2457 mhz 20 mhz width channel regulatory rule:
[ 7.195010] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195012] cfg80211: updating information on frequency 2462 mhz 20 mhz width channel regulatory rule:
[ 7.195014] cfg80211: 2402000 khz - 2472000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195015] cfg80211: updating information on frequency 2467 mhz 20 mhz width channel regulatory rule:
[ 7.195017] cfg80211: 2457000 khz - 2482000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195019] cfg80211: updating information on frequency 2472 mhz 20 mhz width channel regulatory rule:
[ 7.195021] cfg80211: 2457000 khz - 2482000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.195022] cfg80211: updating information on frequency 2484 mhz 20 mhz width channel regulatory rule:
[ 7.195024] cfg80211: 2474000 khz - 2494000 khz @ khz), (600 mbi, 2000 mbm)
[ 7.317383] ieee80211 phy0: selected rate control algorithm 'minstrel_ht'
[ 7.317842] registered led device: rt2800pci-phy0::radio
[ 7.317858] registered led device: rt2800pci-phy0::assoc
[ 7.317871] registered led device: rt2800pci-phy0::quality
[ 7.439075] cfg80211: updating information on frequency 2412 mhz 20 mhz width channel regulatory rule:
[ 7.439079] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439081] cfg80211: updating information on frequency 2417 mhz 20 mhz width channel regulatory rule:
[ 7.439083] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439085] cfg80211: updating information on frequency 2422 mhz 20 mhz width channel regulatory rule:
[ 7.439086] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439088] cfg80211: updating information on frequency 2427 mhz 20 mhz width channel regulatory rule:
[ 7.439090] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439091] cfg80211: updating information on frequency 2432 mhz 20 mhz width channel regulatory rule:
[ 7.439093] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439095] cfg80211: updating information on frequency 2437 mhz 20 mhz width channel regulatory rule:
[ 7.439097] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439098] cfg80211: updating information on frequency 2442 mhz 20 mhz width channel regulatory rule:
[ 7.439100] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439102] cfg80211: updating information on frequency 2447 mhz 20 mhz width channel regulatory rule:
[ 7.439104] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439105] cfg80211: updating information on frequency 2452 mhz 20 mhz width channel regulatory rule:
[ 7.439107] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439108] cfg80211: updating information on frequency 2457 mhz 20 mhz width channel regulatory rule:
[ 7.439110] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439112] cfg80211: updating information on frequency 2462 mhz 20 mhz width channel regulatory rule:
[ 7.439114] cfg80211: 2402000 khz - 2472000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439115] cfg80211: updating information on frequency 2467 mhz 20 mhz width channel regulatory rule:
[ 7.439117] cfg80211: 2457000 khz - 2482000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439119] cfg80211: updating information on frequency 2472 mhz 20 mhz width channel regulatory rule:
[ 7.439120] cfg80211: 2457000 khz - 2482000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439122] cfg80211: updating information on frequency 2484 mhz 20 mhz width channel regulatory rule:
[ 7.439124] cfg80211: 2474000 khz - 2494000 khz @ khz), (300 mbi, 2000 mbm)
[ 7.439126] cfg80211: world regulatory domain updated:
[ 7.439127] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.439129] cfg80211: (2402000 khz - 2472000 khz @ 40000 khz), (300 mbi, 2000 mbm)
[ 7.439131] cfg80211: (2457000 khz - 2482000 khz @ 20000 khz), (300 mbi, 2000 mbm)
[ 7.439133] cfg80211: (2474000 khz - 2494000 khz @ 20000 khz), (300 mbi, 2000 mbm)
[ 7.439135] cfg80211: (5170000 khz - 5250000 khz @ 40000 khz), (300 mbi, 2000 mbm)
[ 7.439136] cfg80211: (5735000 khz - 5835000 khz @ 40000 khz), (300 mbi, 2000 mbm)
[ 7.455169] input: imps/2 generic wheel mouse /devices/platform/i8042/serio1/input/input3
[ 7.801428] hda intel 0000:00:14.2: pci int -> gsi 16 (level, low) -> irq 16
[ 7.856089] hda intel 0000:01:00.1: pci int b -> gsi 19 (level, low) -> irq 19
[ 7.856141] hda intel 0000:01:00.1: irq 43 msi/msi-x
[ 7.856160] hda intel 0000:01:00.1: setting latency timer 64
[ 8.468750] vesafb: framebuffer @ 0xd0000000, mapped 0xf9f80000, using 3904k, total 3904k
[ 8.468753] vesafb: mode 1152x864x32, linelength=4608, pages=0
[ 8.468755] vesafb: scrolling: redraw
[ 8.468757] vesafb: truecolor: size=0:8:8:8, shift=0:16:8:0
[ 8.468899] console: switching colour frame buffer device 144x54
[ 8.468919] fb0: vesa vga frame buffer device
[ 9.262968] ext4-fs (sdb5): re-mounted. opts: errors=remount-ro
[ 9.414896] ext4-fs (sdb6): mounted filesystem ordered data mode. opts: (null)
[ 10.103185] type=1400 audit(1308953491.565:8: apparmor="status" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=922 comm="apparmor_parser"
[ 10.103506] type=1400 audit(1308953491.565:9): apparmor="status" operation="profile_load" name="/usr/sbin/cupsd" pid=922 comm="apparmor_parser"
[ 10.231067] type=1400 audit(1308953491.693:10): apparmor="status" operation="profile_replace" name="/sbin/dhclient" pid=941 comm="apparmor_parser"
[ 10.231344] type=1400 audit(1308953491.693:11): apparmor="status" operation="profile_replace" name="/usr/lib/networkmanager/nm-dhcp-client.action" pid=941 comm="apparmor_parser"
[ 11.649036] r8169 0000:02:00.0: eth0: link down
[ 11.649043] r8169 0000:02:00.0: eth0: link down
[ 11.649372] addrconf(netdev_up): eth0: link not ready
[ 11.922986] addrconf(netdev_up): wlan0: link not ready
[ 13.447625] r8169 0000:02:00.0: eth0: link up
[ 13.447812] addrconf(netdev_change): eth0: link becomes ready
[ 13.595985] fglrx_pci 0000:01:00.0: irq 44 msi/msi-x
[ 13.596489] [fglrx] firegl kernel thread pid: 1210
[ 13.596534] [fglrx] firegl kernel thread pid: 1211
[ 13.596613] [fglrx] firegl kernel thread pid: 1212
[ 13.596833] [fglrx] irq 44 enabled
[ 13.913517] ext4-fs (sdb5): re-mounted. opts: errors=remount-ro,commit=0
[ 13.937501] ext4-fs (sdb6): re-mounted. opts: commit=0
[ 14.514876] [fglrx] gart uswc size:628 m.
[ 14.514879] [fglrx] gart cacheable size:247 m.
[ 14.514883] [fglrx] reserved fb block: shared offset:0, size:1000000
[ 14.514885] [fglrx] reserved fb block: unshared offset:fe07000, size:1f9000
[ 14.514887] [fglrx] reserved fb block: unshared offset:1fffb000, size:5000
[ 22.475850] hda-intel: irq timing workaround activated card #1. suggest bigger bdl_pos_adj.
[ 22.493408] ext4-fs (sdb5): re-mounted. opts: errors=remount-ro,commit=0
[ 22.495379] ext4-fs (sdb6): re-mounted. opts: commit=0
[ 24.312014] eth0: no ipv6 routers present

6) $ sudo lshw -c network
*-network
description: ethernet interface
product: rtl8101e/rtl8102e pci express fast ethernet controller
vendor: realtek semiconductor co., ltd.
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 02
serial: 10:78:d2:89:33:46
size: 100mbit/s
capacity: 100mbit/s
width: 64 bits
clock: 33mhz
capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3lk-napi duplex=full ip=192.168.1.101 latency=0 link=yes multicast=yes port=mii speed=100mbit/s
resources: irq:42 ioport:e800(size=256) memory:fdfff000-fdffffff memory:fdfe0000-fdfeffff memory:feae0000-feafffff
*-network
description: wireless interface
product: ralink corp.
vendor: ralink corp.
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 00
serial: 00:0c:0b:44:b8:4a
width: 32 bits
clock: 33mhz
capabilities: pm bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=rt2800pci driverversion=2.6.38-8-generic firmware=0.11 latency=64 link=no maxlatency=4 mingnt=2 multicast=yes wireless=ieee 802.11bgn
resources: irq:20 memory:febf0000-febfffff

7)$ iwlist scan
lo interface doesn't support scanning.

eth0 interface doesn't support scanning.

wlan0 no scan results

8) $ lsb_release -d
description: ubuntu 11.04

9)uname -mr
2.6.38-8-generic i686

10)(cable not connected eth0)
sudo /etc/init.d/networking restart
* running /etc/init.d/networking restart deprecated because may not enable again interfaces
* reconfiguring network interfaces... [ ok ]

10) (with cable connected eth0)
sudo /etc/init.d/networking restart
* running /etc/init.d/networking restart deprecated because may not enable again interfaces
* reconfiguring network interfaces... ignoring unknown interface eth0=eth0.


not wrong. try setting manually no avail not know if did well. ralink downloaded rt2860sta , compiled , did not work. went install ubuntu 11.04 , change nothing above have right in machine.

thank can provide.

el_

may see:

code:

lspci -nn | grep network

the title of thread refers rt2860 don't see loaded in lsmod. have blacklisted? shouldn't necessary compile it; it's included in kernel default.

Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [SOLVED] wireless not connecting winstars-N WS-WNP671N PCI (Ralink RT2860STA)

Ubuntu